Code for interior glass door decoration constructi

2022-07-22
  • Detail

Interior decoration is a very important thing, because the quality of interior decoration is directly related to the comfort of living in the future, and glass door decoration is a more important part of decoration. If you want to do a good job of interior glass door decoration, you must understand some relevant construction process specifications about interior glass door. Next, I will introduce the construction specifications for interior glass door decoration, hoping to help you

interior decoration is a very important thing, because the quality of interior decoration is directly related to the comfort of living in the future, and glass door decoration is an important part of decoration. If you want to do a good job in the decoration of interior glass doors, you must understand some relevant construction process specifications about interior glass doors. Next, I will introduce the construction specifications for interior glass door decoration, hoping to help you

interior glass door decoration construction specification I. fixed glass installation

1. The installation of fixed partition wall should be carried out after the construction of other indoor processes is basically completed. The fixed glass partition and movable glass door leaf must be set out and positioned uniformly, and the positioning line of the partition and glass door must be set out according to the requirements of the design drawing to determine the position of the door frame, and accurately measure the ground elevation and the top elevation of the door frame

2. Install the glass partition wall, and the width of the limit groove on the top of the door should be 2 ~ 4mm greater than the thickness of the glass, and the groove depth should be between 20 ~ 30mm for glue injection. The installation method can lead out two metal decorative panel sidelines from the snapped center line, and then install the limit slot on the top of the door frame according to the sidelines. The wooden base plate in the notch is used to adjust the depth of the groove. Adjust by increasing or decreasing the base plate

3. Install wooden bottom support with metal finish. The installation method can nail the square wood on the original embedded wood brick, or nail the square wood through expansion bolts to fix the square wood on the ground, and then glue the metal decorative panel on the wooden square with universal glue. Aluminum alloy square pipe can be fixed on the frame column with aluminum angle or on the wooden brick embedded in the ground with wood screws

4. Install the rigid door frame. Nail the square timber of the door frame according to the snapped center line, and then use plywood to determine the overall dimension and position fixation of the door frame column (note that the size of the decorative surface should be deducted). Finally, the metal decorative surface shall be wrapped. When wrapping, the facing butt joint shall be placed in the middle of both sides of the installation glass. The joint position must be accurate and vertical

5. Glass installation. Use a glass sucker (or glass sucker machine) to suck the thick glass tightly, and then hold the sucker handle by hand, and lift the thick glass plate and stand it up by 2 ~ 3 people, and move it to the installation site for preparation. Positioning method: insert the upper part of the glass into the limit slot on the top of the door frame, and then put the lower part of the glass on the bottom bracket to align the center line, and align the installation position of the door frames on both sides, so that the edges on both sides of the thick glass just seal the metal facing seam of the door frame, and it is required that the facing seam is invisible inside and outside

6. Glass fixation. Nail two flat square wood strips inside and outside the bottom joist to clamp the thick glass in the middle, but leave a gap of about 4mm from the thick glass plate, and then paint all-purpose glue on the flat square wood strip to stick the decorative metal plate on the square wood and two flat square wood strips

7. Inject glass glue for sealing. Inject glass glue into the gap on both sides of the top root slot, both sides of the bottom support glass notch and the butt joint between the thick glass and the door frame column. The injection sequence shall start from the end of a gap to the end, and there shall be no pause in the middle. The main points of operation are as follows: hold the caulking gun tightly with even force, and at the same time, the speed of moving along the gap should be even, that is, with the extrusion of glass glue, move the glue injection port at a uniform speed, so that the glass glue forms a uniform straight line at the gap. Finally, scrape off the excess glass glue with a plastic sheet and wipe off the glue with a clean cloth

8. Docking between glasses. The thick glass plate of the fixed part must be assembled with two or more pieces due to its large width. The alignment and splicing of the two pieces will inevitably form a joint, and a distance of 2 ~ 3mm should be reserved for the butt joint (the glass cut of the butt joint must be reversed). After the glass is fixed, the glass glue should be inserted into the gap. After filling, the plastic sheet should also be used to scrape the glue flat, so that the gap forms a clean and uniform straight line. The glue trace on the glass surface should be wiped with a clean cloth

interior glass door decoration construction specifications II. Key points for the installation of movable glass doors

1. Install the upper and lower crosspieces respectively on the thick glass that has been cut and chamfered, and set the height of the door leaf (including the upper and lower crosspieces). If the height of the door leaf is not enough, it can be adjusted by filling the glass edge of the upper and lower crosspieces with thin wooden plywood strips. If the height of the door leaf exceeds the installation size, You need to ask professional glassmen to cut the excess part of the thick glass door leaf, so the glass height of the door leaf would rather be short than too high

2. After the height is determined, the glass should be fixed with the upper and lower crosspieces immediately. The method is to insert small wooden strips into the gaps on both sides of the thick glass and the upper and lower metal crosspieces at the same time, and tap them gently, then inject glass glue between the small wooden strips, the thick glass and the metal crosspieces, and finally seal the gap between the glass and the metal crosspieces with glass glue

3. Positioning and installation of glass door leaf: first, pull the positioning pin on the door frame beam out of the beam plane 1 ~ 2mm with its own adjusting screw Then erect the glass door leaf, align the hole position of the rotating pin connector in the lower cross stop of the door leaf with the rotating pin shaft of the ground spring, and rotate the door leaf to put the hole position on the pin shaft. Then rotate the door leaf 90 with the pin shaft as the axis. (pay attention to straighten the door leaf when rotating) so that the door leaf is at right angles to the cross beam of the door leaf. At this time, align the hole on the rotary connector in the transom on the door leaf with the locating pin on the door frame beam, and pull out the locating pin, insert it into the hole on the rotary pin connector of the transom on the door leaf for about 15mm, and the door leaf can be opened and closed

interior glass door decoration construction specifications III. installation of glass door handle

when cutting the glass door leaf and chamfering the edge, the hole for installing the door handle should be punched at the same time. The connecting part of the installation handle cannot be very tight when inserting into the glass door handle hole, but should be slightly loose. If it is too loose, wrap the insertion part with soft tape. Before installation, apply a little glass glue on the glass part of the handle. When assembling the handle, tighten the fixing screws after its root is close to the glass to ensure that the handle is not loosened at all

editor's summary: that's all for the construction specification of interior glass door decoration. I hope it will be helpful to you. If you want to know more about it, you can pay attention to the information

绍兴男科医院

上海性病医院

长沙妇产医院

Copyright © 2011 JIN SHI